Suchergebnisse für "Factsheet: Energietechnologien gestalten, die für alle sinnvoll und nutzbar sind"
OptiMAS - Optimization of building energy efficiency through model-based energy flow analysis with non-invasive sensors
Using a model-based energy flow analysis supported by non-invasive sensor technologies OptiMAS investigated how to monitor, analyze and optimize existing buildings independent of the installed HVAC systems and automation components. With the OptiMAS approach the optimization potential of individual buildings up to entire areas can be detected, located and tapped by adjustment of system parameters to ensure highest energy and resource efficiency.
IEA HPT Annex 57: Showing flexibility benefits through heat pump implementation in multi-vector energy systems and thermal networks
This project analyzes the future implementation of heat pumps in multi-vector energy systems and thermal networks. The aim is to increase the flexibility of the energy system and to use it for various applications, e.g. for system services or to participate in different electricity markets. Using international case studies, influencing factors and potentials for flexibility options will be evaluated and suitable business models will be derived.
IEA HPT Annex 64: Safety measures for flammable refrigerants
New bans on chemicals and the revision of the so-called F-Gas Regulation pose new challenges for the heat pump and refrigeration industry. In this project, new knowledge regarding the safe future use of flammable refrigerants in heat pump and refrigeration systems up to 50 kW for room temperature control and hot water preparation is being developed and made available to the relevant target groups.
IEA HPT Annex 59: Heat Pumps for Drying Processes
Drying processes are highly energy-intensive and widespread in industry and commerce as well as in households in various forms. In this project, the potential for energy savings in drying processes in various applications will be investigated, which can be tapped through the use of heat pumps and made available to the relevant target groups in the form of guidelines, data, etc.
Photonic Cooling – Efficient cooling of buildings through the use of photonic
Within the scope of the project a photonic cooling approach was investigated and evaluated in terms of feasibility and cost efficiency for building applications. In particular cost-efficient photonic surfaces and concepts were investigated which need to have a high reflectivity in of the incident solar radiation (>97%) and a high emission coefficient within the spectral range of 8 – 13 micrometer in order to enable the emission of heat into the sky.
SUPROMED: Reprocessing and Reuse of Single Use Medical Devices in the Light of Sustainable Development Criteria - Implementation in Austria
In contrast to other countries there is currently no reprocessing and reuse of single use medical devices in Austria. Thus the potential for major ecological and economical savings remains unused. In a stakeholder dialogue, practical implementation strategies were developed to change the trend towards a sustainable value-added chain.
Biomimetic potentials - Interdisciplinary identification and preparation of innovative biological inspired key technologies for "Plus-energy buildings of the future"
Experts from various branches of industry and research as well as bionics representatives worked out innovative ideas regarding "Key technologies for Plus-Energy-Buildings". The results provide a collection of emergent bionic research potential for the implementation of innovative research in the Austrian building sector.
Possibilities of urban high-rise multi-storey buildings in a timber-frame method with target course eight or more floors
Research of urban high-rise multi-storey buildings in a timber-frame construction method. Fundamental clarification of the feasibility in relation to the supporting structure, fire prevention and security. SWOT analysis as well as economic, ecological research concerning sustainable design.
LEKOECOS - combined economic-ecological life cycle assessment model
The consumption of ecological and economic resources over the whole life cycle is supposed to be anticipated and optimised in the design process of buildings and refurbishments. A combined life cycle assessment model together with an economic-ecological base element catalogue considering the klima:aktiv criteria was developed based on the structure of the life cycle cost model LEKOS and the ecological valuation tool Ecosoft.
IEA EBC Annex 62: Ventilative Cooling
The main goal of the Annex 62 is to make ventilative cooling an attractive and energy efficient cooling solution to avoid overheating in buildings. Ventilation is already present in buildings through mechanical and/or natural systems and it can remove excess heat gains as well as increase air velocities to widen the thermal comfort range. The results from the Annex facilitate better possibilities for both design purposes and for energy performance calculation.
IEA EBC Annex 89: Ways to Implement Net-zero Whole Life Carbon Buildings
IEA EBC Annex 89 focuses on the pathways and actions needed by various stakeholders and decision-makers to implement whole life cycle based net-zero greenhouse gas (GHG) emissions from buildings in policy and practice. Annex 89 will support key stakeholders and decision-makers in developing and implementing effective Paris-goal compatible schemes and solutions to achieve NetZ-WLC buildings at multiple scales.
IEA EBC Annex 86: Energy Efficient Indoor Air Quality Management in Residential Buildings
Residential buildings should be able to provide good indoor air quality while ensuring high comfort and low energy use at lowest possible cost. This project will develop methods and compile data to evaluate different indoor air quality management strategies. Furthermore, innovative control strategies will be evaluated and tested in order to develop concrete recommendations for possible implementations of innovative ventilation systems for residential buildings.
IEA EBC Annex 91: Open BIM for Energy Efficient Buildings
Building Information Modeling (BIM) is considered a key technology for optimising the overall energy performance of buildings. The project lays the foundations for OpenBIM tools to include the assessment and optimisation of the energy efficiency of buildings in the future, for Open BIM processes and data models to be increasingly harmonised and standardised, and thus for smaller construction companies to have the opportunity to work on complex BIM projects in the future.
IEA ISGAN Annex 5: Smart Grids International Research Facility Network (SIRFN). (Working period 2021-2022)
The Smart Grids International Research Facility Network (SIRFN) aims at improving the implementation of Smart Grids technologies by collaboration between smart grid testing facilities, test beds, and large-scale demonstrations. In the working period 2021-2022, the focus will be laid on the development of extended interoperability tests for decentralised energy resources and micro grids.
IEA ISGAN Annex 5: Smart Grids International Research Facility Network (SIRFN). (Working period 2013-2018)
The Smart Grids International Research Facility Network (SIRFN) aims at improving the implementation of Smart Grids technologies by collaboration between smart grid testing facilities, test beds, and large-scale demonstrations. By active participation, Austria’s position and leading role on the forefront of international Smart Grids development has been strengthened.
IEA SHC Task 48: Quality Assurance and Support Measures for Solar Cooling
The completed IEA SHC Task 48 focused on an enhanced quality improvement and market-support measures for the technology option ‘solar thermal cooling or air-conditioning'. In cooperation with a total of 22 organizations (12 research institutes, 5 universities and 5 companies) from eight countries numerous useful reports and tools have been created to improve the quality of solar cooling systems with significant contribution of the Austrian partners.
URBAN STRAW - Fire protection conditioning of blow-in straw insulation material and its structural application for urban building classes 4 and 5
Investigation and development of fire protection conditioning of chopped straw blow-in insulation based on biogenic flame-retardants of similar building materials and their application methods. Use of the material as external thermal insulation in material-reduced prefab timber construction elements for urban building classes 4 and 5 up to 6 storeys.
SAVE circular approaches for green buildings!
The project demonstrates the cycle and use of synergies in an ARWAG residential building from the extraction of valuable raw materials through a urine treatment plant (fertilizer) using energy recovery measures (heat recovery, heat pump, photovoltaics) to the use of the fertilizer for the generously designed greening measures and the associated effects on the microclimate.
ParaSol - Multifunctional solar canopies for urban streets and places
With the city of Leoben as a use case this exploratory project will, for the first time ever, examine the spatial effects, synergy- and energy potentials of newly developed wide-span light-weight solar canopies for streets and squares in urban public space as well as their implications on the townscape, the image of the city and the city function.
Energy relevant and ecological monitoring studies of demonstration buildings, which were built in the framework of the program "Haus der Zukunft".
Energy relevant and ecological monitoring studies of demonstration buildings, which were built in the framework of the program "Haus der Zukunft". The user acceptance should also be levied and displayed