Suchergebnisse

WHISCERS. Whole House In-Situ Carbon & Emission Reduction Solution

Whiscers is a system for installing internal wall insulation with minimal mess, whilst the resident remains in the property. It involves measuring the walls in the property using a laser device that enables fast and highly accurate measurement. Information is then sent electronically to a computer controlled off-site cutting machine that is rapid, precise and mess-free.

Photovoltaic solar modules for building integration

Development of new manufacturing technique for photovoltaic solar modules, which fulfil the special requirements of building integration.

smart façade - energy potential of adaptive façade systems

A specially developed simulation model is employed to ascertain the energetic potential of adaptive façade systems. The dynamic behavior of the physical properties of the adaptive façade system reacts to both internal and external changing conditions. The goal was the development of an adaptive façade, which helps provide maximum comfort for the building occupants with minimum energy consumption.

BIM2BEM Flow - Continuous BIM-based energy efficient planning

Automated integration and assignment of exchange requirements between the design and simulation programs, based on the elaborated exchange information requirements, should enable continuous energy efficiency planning along the design phase.

THERM-opti-BALCONY: Thermal Optimized Renovation of Balconies

Pre-cast cantilever balconies represent a particular problem in the thermal renovation of buildings. The central goal of this project is the development of practical and cost-effective mounting solutions for the thermally decoupled reconstruction of balconies on building frontages and achieving a significant increase in the energy performance of the thermal renovation measure.

MODESTORE - Modular High Energy Density Sorption Heat Storage

Seasonal storage of solar heat for use in low energy and passive houses (new buildings as well as old buildings).

Development of a clay - buildingboard with a surface ready to paint

Development of a building board consisting of a wood fibre board, coated with clay-plaster reinforced by natural plant-fibres (BioFaserLehm) for reinforcing planking of timber-constructions and also for statical not stressed inner wall surfaces.

Research work on outside sprayed-on cellulose insulation covered with plastering

This research work was done to expand knowledge about outside sprayed-on cellulose insulation application focusing on mechanical and physical properties respectively.

3D*3B - 3D-Concret Printing, Reinforcement for low carbon and bending stressed structures.

The project is about 3D printed structural elements and their integration in building structures. The focus is predominantly set on bending stresses structural elements like panels and slabs. Results will point out technical, logistic and climate relevant aspects.

BIM4BIPV - Future aspects of building-integrated photovoltaics (BIPV) in cross-system BIM planning

Research into an end-to-end BIM planning flow for energy-optimised, building-integrated photovoltaics (BIPV) that simultaneously generates solar energy, enables optimal use of daylight and provides shading.

baubookPlus - Expansion of an extensive knowledge database of sustainable buildings

By the foundation of the baubook GmbH in 2008 the two databases of building products "öbox" and "ixbau.at" have been merged. The new database baubook was expanded. Essential functions (central product declaration, decentral quality management) and fields of products were added.

Walchfenster04 - from a functional model to a serial production-oriented prototype

Technical preparation of the functional model from the window and facadesystem walchwindow04 to a serial production-oriented prototype. Developing the new production processes and technologies

Development of thermal solar systems with unproblematic stagnation behaviour

Research on the influence of collector hydraulics, piping and the arrangement of plant components on the stagnation behaviour of thermal solar systems.

smartEXT - extended application boundaries for proven passive house technology

The present study aims to explore the application options for compact units (ventilation devices including micro heat pumps, developed for passive houses) in low energy buildings. Compact ventilation units for heat recovery, heating and domestic hot water shall bear the basic heating load, whereas peak loads shall be covered by newly-developed auxiliary heating equipment combined with intelligent control algorithms. This allows increased energy efficiency as well as cost effectiveness together with higher living quality and lower ecological load.

Mechanical ventilation system for windows for the renovation of old buildings

Analysis and implementation of alternative ventilation systems for windows, focusing on thermal renovation of old buildings. The investigated ventilation systems were presented to an expert group. The aim was to discuss ventilation technologies with the help of different aspects and to develop a SWOT analysis.

SOLROSE FP - bionical designed solarthermal collector, final product developement

Archieved goal was the final product developement oft he innovative solarthermal collector SOLrose from prototype to seriel production. Enhancements of SOLrose with respect to the state oft he art: attractive design for frontage integration, serial production of system modules, distribution and assembling.

Solar Adsorption cooling system of residential and office buildings (SunSorber)

In the on hand project an adsorber/desorber for a solar operated/district heating operated one-level adsorption chiller with water as cooling agent and silica gel as adsorbent agent will be planned for a low range of performance (2 to 50 kW refrigerating capacity). It will be implemented as a test-/pilot plant. Hence these two substances are an alternative to the HFCKW´s cooling agents that are used nowadays.

Sprayed-on and Plaster-covered Cellulose-insulation without vapour barrier

Investigations on the fundamental suitability of sprayed-on and plaster-covered cellulose insulation for thermal insulation of buildings.

LowEnergyBuildingServices - Highly efficient presence detectors and end user technologies

Highly energy efficient presence detectors, control systems for sun shades etc. are de facto not available on the market. Regarding plus-energy office buildings, the minimisation of the power consumption of these components is a central criterion to achieve the "plus" part in terms of the energy of the building. A highly energy efficient presence detector was successfully sketched in this project, which undercuts the intended standby consumption of 0,05 W.

An innovative approach for facades with optimised noise protection and natural ventilation

The aim of this project was to advance the state of the art in the engineering of double-leaf building facades that facilitate natural ventilation while providing sufficient sound insulation. Realization of natural (window) ventilation is in some instances difficult due to a number of factors. Thereby, noise pollution (especially traffic noise) plays an important role. To address these issues, the project explored innovative solutions in terms of facade constructions for concurrent natural ventilation and noise control.